10 cm bench vise, 19 kN force, steel and cast iron

pretty nice vice

the vice is HD and machined well for the money its amazing. I will note to the buyer. the crank that comes with the vice Falls off. when I have some time I will drill and tap a spot for a set screw but well worth the purchase.

Good vice for the $$, can also be improved.

Good small mill vice for much less money than the pro brands. ground surfaces are within the tolerances you would expect. Some cost savings have been taken like hidden surfaces under fixed and moving jaws are not ground. If you have the means to grind or scrape these, then a very good vice can be had for small cost and a little effort.

5" super lock vise

Heavy vise that is sturdy, accurate and easy to mount.

Impressive vice

This is a very impressive machine vice, especially considering the price. Thank you

Manufacturer engraver

Strong and massive, straight, jaws straight, strong grip. Fast shipping, cheap and professional. Will buy again

Start up business

I was very surprised by the high quality of this vice vs the price. Old beat up vises this size cost 3x as much and other brands are $500 to $600. Very satisfied with all my purchases!

Helt nöjd med detta köp

Mycket prisvärda skruvstycken. Tror backarna är inslipade efter montering. Snabb leverans och väl förpackade.

Quality control issues

I ordered two vises in hopes they were close to the same height so I could hold one long piece of aluminum with the two vises. Height difference was almost 1mm.

Mr.

Overall is a good buy. I would prefer a lower profile for my milling machine. Straight flat surfaces. For a garage work is pretty decent. Good price also.

Good product👍

A good product for the price and can be recommended👍

Retired home inspector

The vise is very impressive in all aspects. My only concern was the packaging. It appeared that the box was dropped during transport and subsequently the foam packaging was broken in some cases but the vise was not damaged. As a result of the damage, the manual was scuffed and torn beyond repair. I was unsuccessful in obtaining a replacement copy via your online service and unfortunately did not find a download version in the internet.

Nice piece!

A real heavyweight that the post office had a bit of a struggle with. A lovely, precise vice. I just filed down a few sharp edges on the underside, but at this price it’s unbeatable. It’s precision-made and, thanks to the design of the guide, it doesn’t pull the clamped material upwards like a simple vise that is used normally with a column drill.

Good for the money.

This is a decent little drill press. And it has a bunch of nice features, including a digital read out for rpms. The truck had some run out. And it’s not that Ridgid. But for the price, I don’t think you could really beat it.

Me

Perfect for my milling machine and not too expensive ✅✅

Mr

bought it for my shaper resto and it works great would of got the 6inch but not avialabe at the time still a very strong and well built vise

DIYer

Fits well on my small milling-drilling maschine, acured construction but the jaws are not hardened ?

Excellent vise for the price

Nice vise, quality is good. Just need to remove a few sharp edges on the finish. Accurate to .0002 on the jaws. Would buy again

Retired Machinist

Very good quality and workmanship. I definitely have no second thoughts about this purchase. Operates very smoothly and hold solidly during heavy cuts made with mill.

Owner

Completely misrepresented in the photos and description. This vise does not have ACME threads. It has standard metric bolt threads. This is a huge difference in the quality of the vise. The vise at this price point will do everything thing I need it to do, but I was expecting it to match the ad and pictures.

Great Value

1. Price) Great value for this item. 2. Quality) On par with my other pro-level equipment. 3. Features) Great set of features. 4. Easy to use) Very easy to use and set up.

Decent price for the price.

Mounts easily, feels heavy duty and weighs a lot. Jaws are not parallel. Threads are really tight and hard to turn. Takes 2 hands to turn if not bolted down. 1 to hold the vice while you turn the handle with the other. As much as it weighs the handle should spin freely.

5-inch ACCU Lock vise

Unit appears to be well made and measures square across vise jaws. Is very heavy and works well on my bench top milling machine. Vice screw does bind a little and requires using a wrench to adjust. Definitely an offshore product but cost hundreds less than name brands and will work for my hobby machining. Might be a little big to use on a smaller drill press.

finish was appalling and the accuracy was not up to spec.

The cast recesses for hold-down had large areas of razor sharp jagged areas, a serious injury risk. No de-burring was done anywhere, even the chamfers needed de-burring! The whole unit was full of casting / machining grit, cast flashing and required a complete tear-down and degrease / wash out and finishing with a rotary burr. The machined recess for the thrust washer had a large sliver of metal which caused jamming. The fixed jaw had 0.15mm of vertical run-out.

.

Arrived in good time, well packed and in good condition. The finish is excellent and it is easy to use.

Mr

Very nicely built - good quality and not a lot of cleaning up before using. Accurate

Hobbist

I gave this vice 5 stars because i think it is well worth the money for what it is. I'm using it on a 6x26 knee mill to hold parts that are just a little too big for my 4". It was easy to indicate in and is flat to the table. Again, for the money I think it is well worth it. Like all imports, it needs a good cleaning and deburring but completely acceptable for hobby work.

Mr

Excellent product, beautifully manufactured and fits well on my milling machine,. recommend the brand to trade with.

Diesel Tec

Very Nice for the Price! I don't use it every day. Home Shop use.

4 Inch Milling Vise with swivel base

TL-DR: I'm overall satisfied because I expected that the price meant I was getting a fairly decent casting, machined and ground that requires further cleaning, deburring and refinement. The paint is very decent and overall surface finish more than decent. - Received promptly in good condition by pure luck since there is ZERO protection in the box. - No rust on mine*, only grime and machining swarf and some sticky oil/grease partially dry. - *Not everything is coated and in a cold climate, it got full of condensation. Unpack, degrease and clean and coat with WD-40 immediately.* All the immediately visible machined surfaces look good, but EVERYTHING needs cleaning and DEBURRING. A complete teardown shows some casting defects (minor) and not as good machining where it is "hidden", and more involved deburring and filing is needed to address that. ***The nut that sets the pressure against the thrust bearing for the lead screw has 2 set screws which damage the threads. - The bearing and leadscrew need to be cleaned and re greased. - Yes, one can use it out of the box, it works, but it will probably grind itself over time and even draw blood when handling. Conclusion: After a couple of ho…

The product is super, good work and finish is good.

The product is super, good work and finish is good.

Ms

Great Service fast and as stated. Machine is working well so far no complaints.

Bigger than I thought

It's bigger and heavier than I thought. Have tested it a little, but not put it to work yet:)

Great product

Very good

Good Quality for the price point

Good quality for the price point

Ruuvipuristin

Hyvä ruuvipuristin harrastuskäyttöön

Great vice

Good value for the money

Gets the job done.

Affordable vise for a Bridgeport.

bra skruvstycke

funkar bra. rejält skruvstycke

Machinist

Excellent for the great price

Mr

Great little vice for the mill

Engineer

Excellent vise, very well built!

Alles wie versprochen!

Tut genau wie beschrieben

Master

Best vice ever for the price. Thank you

Mechanic

Great tool

Very good

Perfect :-)

Consumer

Not bad for the price

mar

super

X

Recomended this product.

Schraubstock für Fräßmaschine

Gekauft für meine Fräßmaschine starke Ausführung sehrgute qualität

Hyvä penkki

Hyvä ja tukeva ruuvipenkki. Tarkasti koneistettu. Ainoa mitä ihmettelen ovat mukana tulleet "kiinnityspalikat". Eivät sovi vakio T-uraan eivätkä mukana tulleet ruuvit olisi siihen riittäneetkään. Palikat ovat onneksi sopivan korkuisia, että sopivat vestiraudan toiseen päähän. Muuta käyttöä en niille keksinyt.

Perfecta.

Como la recomendó Michel, del canal TR Pressicion Machining... la pedí. Me ha parecido espectacular, no soy muy fan de las bases giratorias, pero esta pesa mas que la propia mordaza aunque en la imagen no se ve. Es super fuerte. Gracias Michel, lo que dices va misa.

Lo práctico

Es un gran producto y estoy muy satisfecho con ello con el tornillo

Funciona perfecto sin holguras

Buen producto y buena calidad, lo uso para una fresadora llevo poco tiempo usándolo pero la verdad es que va increíble lo recomiendo.

Bon Etau de fraisage puissant

Bon étau utilisé sur table de fraiseuse. Il est puissant et offre un bon serrage des pièces à usiner. Assez précis dans l'alignement des mors.