Cortador Plasma 50A, 220V, Visor Digital

Good machine.

Very pleased. So far I've cut lots of 2 and 3mm steel plate, which it cuts extremely fast and clean. I've also cut 12mm plate with absolutely no issues. Overall I'm really pleased with it.

Bonne machine mais :

Suite à quelques utilisations je suis arrivé au moment de remplacer les consommables et malheureusement lorsque je les remplace par les consommables fournis le poste ne fonctionne plus j'en ai donc commandé sur un autre site et idem je ne sais pas où avoir des consommables identiques à l'origine monter sur la torche.

Największe wady przecinarki

Przecinarka robi co ma robić, nie ma się do czego przyczepić- jedynie dwie rzeczy są denerwujące : czas chęcia to tylko 6 sekund - strasznie irytujące, oraz jeszcze większy minus- nie pracuje na przedłużaczu 2 żyłowym musi mieć 3 żyły.

Showed up to wrong place and does not work

Showed up to the wrong place then did not work would like a replacement

mauvais fonctionnement

Bonjour . Malheureusement l'appareil ne fonctionne pas bien . Des la mise en route il s 'allume et en suite s'éteint tout seul plusieurs fois avant de pouvoir commencer a découper.

Werkt prima voor kleine projecten

Werk prima, maar op maximum vermogen op 220v moet je zien dat je een deftige aansluiting hebt. Dun materiaal gaat prima.

Plasma LG 65 amps.

When its arrived it was evening and the voltage on the grid it was low and i set the amperage at 40 to cut something for doing a test. Next morning I do it another test the voltage on the grid it was a litle bit better so I cut with amperage set at 50. At 65 it is imposibile to cut becauee I think the grid 220 v has no power enough thats make me to belive the plasma cutter It has a true power.

Does not work like it should

Would not recommend buying will not cut good like the description says it wont cut thin metal it looks like a bad weld when trying to use it

Ha funzionato bene nelle prime ore. Ma...

Ha funzionato bene per le prime ore, poi ha iniziato a interrompersi a metà taglio. Si è arrivati ​​al punto in cui era difficile mantenere stabile l'arco plasma... Ho comunque finito il lavoro, ma consiglio una marca più costosa, come Telwin, se si deve tagliare molto acciaio. Quando ho finito di tagliare la vecchia caldaia a gasolio, non riusciva più a eseguire tagli lunghi più di un centimetro prima di interrompersi, anche dopo aver sostituito gli ugelli della torcia.

Good for small jobs

It does fine with small cuts but if youre trying to make long cuts it tends to overheat and shut off. Ended up buying an Arc Captain Cut65MP and am so happy I did.

Ultra cheap machine that cuts

This is a decent little plasma for the price. I have used it a few times on some 1/8" SS & Aluminum. It will cut 1/4" carbon steel fairly well but, it's definitely not a heavy duty machine but, if you are just cutting thin metal it will get the job done. Not sure how well it will hold up over time.

Works

Came with everything it said, works as intended

Plazmový rezací stroj výrobca, 60A bezdotykový plazmový rezací stroj s pilotným oblúkom

Plazmová rezačka parádne funguje,10mm hrubé železo odrezalo perfektne bez problému,a aj s dodaním bolo všetko perfektné. Dakujem

Recommended

Very easy to use, excellent for the price. I recommend it

Facile da settare ed utilizzare.

Vista su Youtube, e subito acquistata per uso intensivo.

STOPPED WORKING AFTER 1ST TIME USING

WORKED FOR 170 FEET QUIT, CAN'T GET THEM TO WARRANTY IT.

Big Boss

Je possédais un découpeur plasma de Eastwood le model Versa Cut 60 utilisé 4 à 5 fois dans 10 ans pour bricolage et plus rien ne fonctionne plus, téléphoner la compagnie, département de réparation fermé et appareil discontinué. J'ai parler avec Bill qui m'as suggérer de commander une pièce de $59. et $60. de shipping, échange d'argent et taxes plus de deux cent dollars. J'ai remplacer la pièce et même problème pas d'arc électrique. J'ai rappeler et laissé un message pour Bill et depuis aucune nouvelle. Donc j'ai acheter votre découpeur Plasma que j'ai essayer une fois sur une pièce de métal scrap et fonctionne très bien. L'avenir nous parleras,

Fijne plasma snijder voor weinig geld

Werkt heel goed en is makkelijk in gebruik. Heb er dikke stukken staal mee kunnen snijden zonder moeite. Ik ben benieuwd hoe lang hij het volhoud. tot nu toe totaal 2 uur gebruikt. Enige nadeel is de korte massakabel.

The brand For Life

Love this unit! Easy full set up! Ive used it on 110v and 220v i would highly suggest for home users buy a 110v 30a to 220v Dryer plug adapter and extension cord.

Could use improvement

Received this unit today, set it up and tested it. Instructions beyond labeling of components are non existent. Troubleshooting is for a welder! After a couple of hours of screwing around, I found that 4 of the 5 tips I was shipped were defective and produced only a very weak spark. Luckily one tip worked so I could verify that the unit was operable. The electrodes also look very cheap, so I would recommend shopping for some higher quality consumables right away, and you'll have to Google the settings for air pressure, 2T vs 4T operation, current settings etc. The unit seems ok, but it's frustrating trying to troubleshoot multiple faulty components on a new unfamiliar item. Picture of my faulty parts below for reference.

Fabricatoe

I\n Love my V vor 605 AM plasma cutter. Got it, it was very well packaged and it was very nicely. Assembled, hooked it up to 220 V connected the airlines and gave her the full beans and was able to cut through 7 sixteenths. Steel like a knife through butter. So my settings were 65 amps and 76 lbs of air and i just let it do the work. On 1/4 and 1/8 steel it was nothing to it. I would highly recommend it. However just be careful with the whole torch the procylin is fragile i acidently dropped it and broke mine in two no big deal one zip tie later and i was back up and cutting I would totally post pics and vids but i cant seem to get the formatting correct . No biggie but it does not change the way i feel. I love this unit

Good

Bon rapport qualité prix, à date ça va bien

PENNEY

I WOULD NOT BUY ANY THING WITH the brand ON IT. I PURCHASED A PLASMA TORCH. NOT PLEASED WITH UNIT -CAN NOT GET ANY HELP FROM the brand

Plazma

For cutting thin players it is good, but I needed plazma for 2mm metal cutting so it barely makes it.

Mr

Works very well for what I need cutting 1/4” I didn’t use the air line it came with I would recommend this product

Klein maar krachtig

Dit is mijn eerste plasmasnijder en ben hier wanden tussen zeecontainers aan het verwijderen. Het steuntje om 1.5mm afstand te houden van de plaat heb ik er af genomen en gebruik de tips rechtstreeks tegen de wand. makkelijk in te stellen en doet zijn werk. drukleiding en vochtfilter ga ik mettertijd vervangen maar is zeker functioneel met de standaard bijgeleverde

Love it

Works very good actually what kind of cut quarter inch plate fairly decent definitely a great purchase

J’ai hate de prendre de l’expérience

Cest pas evident a utiliser, le manuel indique aucun shema de branchement ou indication pour reservoir d’air ou debit ect avoir plus d’informations serait surement plus positif

uhum

den är lätt att använda men min gick sönder efter ungefär 20 minuters användande. kan hända tr jag fick ett dåligt exemplar, det vet jag inte men oavsett så fick jag full återbetalning så jag har inget mer än kvaliten att klaga på.

Comme dans le descriptif

Montage facile, réglage facile. J'ai testé su une tôle de 3 mm d'épaisseur et la coupe est propre. Hâte de tester dans du plus épais.

Better than expected.

It cares more about clean ground than anything ive seen, wants it clean and close. But it was very surprising, works very well for the price and we are happy, would buy another. Have only used it on 220v.

Pretty Good Plasma

Pretty good plasma cutter. Priced fairly. Only issue is that the brand does not sell or offer replacement nozzle tips and electrodes.

equipment king

i will be posting a you tube review later

Rictek

I was a little worried about the consumables. But I was able to find them at harbor freight. It's a little slow on ¼" n up but works great on thinner material. For the price it was a good investment. Down the road I'd like to bump up to the 65amp n give this one to my dad. Thank you Rick

Mechanic master

Hi At the verry first day had a broken ceramic part of the torch a und i must buy at Ebay ,because u dont have as spare parts to buy??? Machine working exellent.. Br

Cutter

It is Awsome just use it and it worked great I’m extremely impressed and love all the fab tools have the welder cart and table

lil' machine with big power

Wow.....the value is incredible. this little sucker out-cuts my big machine. I am cutting 1/2 stainless 316 plate. The expendable tips and cups last surprisingly long.....I think the standoff drag cage helps. This machine is so small, light, portable, I take it inside my sculpture easily....yet it has the cutting power of my big machine twice as big and 3x heavier. Hard to believe I got it delivered for only $250 bucks, Viva the brand

Antorcha Floja o defectuosa

Hemos comprado la maquina de corte con plasma 50A sin contacto para probarla e incorporar mas a nuestro taller de formaciones en procesos de soldadura. Tras estar cortando un par de dias con ella podemos decir que la maquina tiene muy buen precio, las calidades están mas que aceptables en cuanto a la maquina, si hablamos de la antorcha es otra historia. dado que la antorcha al llevar dos dias de trabajo cortando, y llevar un mantenimiento adecuado de limpieza de los útiles que esta tiene, a comunicado provocando un agujero en la parte de la rosca que no se puede quitar por el que ahora sale el gas, no saliendo la combustión por la boquilla, sino que sale por la parte posterior a la tobera cerámica. La maquina de potencia va bastante sobrada y tiene un uso bastante sencillo pudiéndola dominar fácilmente en un par de horas sin haber tocado nunca una de ellas. Vamos a intentar ponernos en contacto con la marca haber si nos da una solución ya que no venden en la web las antorchas sueltas.

owner

Loved it! Easy to use. Gotta have enough air pressure.

M

Never used a plasma before but has done what I wanted it for, very pleased.

Unsure...

It is ok for really thin metal. The one that I received however has a defect. It turns off every 10 seconds or so.... Returning

Does not work don’t buy !!!!

Torch burnt up when I went to strike an arc and now it’s junk the money won’t hurt me but it still sucks . Tried a live chat they answered and never could get them back I’ll just use it for target practice I guess

President

I bought two of these to trim the scrap drops off of our laser machine. They both stopped working after about a month of use. JUNK! Don't waste your money.

Owner

I have not used it yet so I can not answer the last question however I will go out on a limb and say I am 100 percent that it will work as it should so looking forward to running it thank you for all you have done.

Thomas

Works great especially for the price must have a compressor that puts out at least 8.5 CFM didn't think it would be very good but it works amazing once you know how to adjust it properly

Not sure

Came with a dent in it even though packaging was not damaged. Wouldn’t maintain an arc. Maybe my inexperience or a compressor issue. Ended up using an angle grinder…

Worker

This item is very bad. It turns off every 3 seconds. Sadly I was not using it sooner, but will try to return it.

Top 👍

Super Gerät Mach was es soll, Löcher in Stahl

65a plasms

No complaints works as said very surprised at how well it proform even on just 110v have had it on 220v yet

Retraiter

Fonctionne très bien et facil a utiliser Prévoir pices au ground la qualité est douteuse

Plasma cutter

Everything came as advertised. Looks like a nice machine quality is good. Could improve on some of the clamps and connections to have quick connection. Air hose connections have not used it yet so not gonna give it my full review yet until a later time after I use it, but so far so good. I put airline quick connect and disconnects on it for ease of use. As you can see in the rear of the machine could be a better type of hose or connection from going to the filter so it’s not getting kinked but overall impressed so far.

Shop

Don't cut like I thought it would it stop cutting in the middle of it. Will not run on 110 alone 220. This not a good buy need to do better

Jack of all trades, master of none

This machine has a very affordable price. I use it at home but I believe it would even work well for shops and many other people beyond the "home hobbiest." Solid build, easy to get to work right out of the box.

plasma 65A

Plasmasnijder snijdt niet zuiver, bij een beetje vermogen klapt de zekeringen eruit C16. Ook aantal reserve delen niet mee geleverd en de meegeleverde delen passen niet goed. Aangezien ik het sporadisch nodig heb dacht ik dat dit een geschikte machine was maar dat valt erg tegen.